Lighting CalculatorPlan light with clear assumptions

Lighting calculators / Screens & projectors

Plan the light. Understand the numbers.

Screen Size & Aspect Ratio Calculator

Diagonal size alone does not determine image area without an aspect ratio. A 100-inch 16:9 image differs from a 100-inch 4:3 image. This geometry calculator reports physical dimensions and square metres so the screen area can be used consistently in a projector flux calculation.

Your lighting inputs

inches
ratio
ratio

Starting values are illustrative. Check units and assumptions below. Calculate submits your inputs to this site’s result page.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Width = diagonal × ratioW/√(ratioW²+ratioH²); height = diagonal × ratioH/√(ratioW²+ratioH²).

Find rectangular image width, height and area from diagonal size and aspect ratio.

  1. Choose a measurement plane and use compatible units for all inputs.
  2. Obtain appropriate product data or representative measurements for the stated model.
  3. Submit the form, then interpret the result with the assumptions and limits below.

This is rectangular geometry, not a projector throw, optical focus or video-wall structural design.

16:9 images and the area used in lumen calculations

Diagonal size alone does not determine image area without an aspect ratio. A 100-inch 16:9 image differs from a 100-inch 4:3 image. This geometry calculator reports physical dimensions and square metres so the screen area can be used consistently in a projector flux calculation.

LED display ratio searches may instead refer to pixel dimensions. A physical image ratio and a pixel ratio coincide only when the pixel geometry and panel arrangement support that assumption. Use actual cabinet and module data for an LED wall rather than inferring resolution from diagonal size alone.

Check the numbers

Screen Size & Aspect Ratio Calculator: calculated examples

These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.

Worked example with stated inputs

Image diagonal = 100 inches; Aspect ratio width term = 16 ratio; Aspect ratio height term = 9 ratio.

OutputComputed result
Rectangular image area2.756767 m²
Image width2.213802 m
Image height1.245264 m
Width87.157554 inches
Height49.026124 inches

How one input changes the answer

ScenarioChanged inputResult
25 inchesImage diagonal0.172298 m²
50 inchesImage diagonal0.689192 m²
75 inchesImage diagonal1.550681 m²
100 inchesImage diagonal2.756767 m²
150 inchesImage diagonal6.202725 m²
200 inchesImage diagonal11.027067 m²
300 inchesImage diagonal24.810901 m²

Unchanged inputs use: Image diagonal = 100 inches; Aspect ratio width term = 16 ratio; Aspect ratio height term = 9 ratio. Results retain the model limitations described above.

Common questions

Does 16:9 mean 16 inches by 9 inches?

No. It is a proportion that can describe many physical sizes.

Can I use a 4:3 ratio?

Yes. Enter 4 and 3 for the ratio terms.

Does this determine projector mounting distance?

No. Throw ratio and lens constraints are separate from image dimensions.

Can I calculate lumens from diagonal size alone?

No. You also need aspect ratio, a defined illuminance or luminance target, and an appropriate optical model.

Which assumptions should I check?

Match the units, measurement plane and equipment boundary stated on this page. The starting values and comparison cases are chosen examples, not universal recommendations or current manufacturer ratings.

Where are the formula references?

Published references are listed at the bottom of this page as plain-text website addresses. The example tables are calculated from the displayed method rather than copied from proprietary tables.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.

  • NIST SP 811 Appendix B.9: photometric unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9