Lighting CalculatorPlan light with clear assumptions

Lighting calculators / LED circuits & power

Plan the light. Understand the numbers.

LED Strip Power Supply Calculator

Use the full-on strip input per metre for the actual product, including the intended color-channel combination. A five-metre strip at 14.4 W/m requires 72 W nominally. Dividing by 24 V gives 3 A before any separate distribution losses. The selected headroom increases the candidate power figure without changing the strip’s nominal demand.

Your lighting inputs

m
W/m
V
%

Starting values are illustrative. Check units and assumptions below. Calculate submits your inputs to this site’s result page.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Strip W = metres × W/m; current = W/V; candidate supply W = strip W × (1 + chosen headroom).

Calculate constant-voltage LED strip load and a stated supply-power allowance.

  1. Choose a measurement plane and use compatible units for all inputs.
  2. Obtain appropriate product data or representative measurements for the stated model.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Headroom is a user assumption, not a universal manufacturer rule. Verify voltage, temperature derating, channel loading, wiring and product-specific operating limits.

12 V and 24 V strips, transformer sizing and LED drivers

Use the full-on strip input per metre for the actual product, including the intended color-channel combination. A five-metre strip at 14.4 W/m requires 72 W nominally. Dividing by 24 V gives 3 A before any separate distribution losses. The selected headroom increases the candidate power figure without changing the strip’s nominal demand.

Constant-voltage strips need a compatible voltage source; bare constant-current LED strings are different. Brand searches such as Ansell, Robus, BTF, Trex or specific landscape transformers still require the product documentation. This calculator does not validate dimmer protocols, waterproof ratings, manufacturer compatibility or thermal conditions.

Check the numbers

LED Strip Power Supply Calculator: calculated examples

These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.

Worked example with stated inputs

Total energized strip length = 5 m; Maximum input per metre = 14.4 W/m; Nominal constant voltage = 24 V; Chosen power headroom = 20 %.

OutputComputed result
Supply power with chosen headroom86.4 W
Nominal strip input72 W
Nominal strip current3 A
Chosen headroom20 %

How one input changes the answer

ScenarioChanged inputResult
1.25 mTotal energized strip length21.6 W
2.5 mTotal energized strip length43.2 W
3.75 mTotal energized strip length64.8 W
5 mTotal energized strip length86.4 W
7.5 mTotal energized strip length129.6 W
10 mTotal energized strip length172.8 W
15 mTotal energized strip length259.2 W

Unchanged inputs use: Total energized strip length = 5 m; Maximum input per metre = 14.4 W/m; Nominal constant voltage = 24 V; Chosen power headroom = 20 %. Results retain the model limitations described above.

Common questions

Can I use this as a 12 V LED power supply calculator?

Yes for a constant-voltage load with a verified W/m rating. Enter 12 V and the actual strip data.

Is 20 percent headroom always required?

No. It is an editable planning choice. The exact supply’s derating and operating instructions control its use.

Does headroom fix voltage drop?

No. Distribution resistance and current cause voltage drop; assess the wiring and feed arrangement separately.

Can I use a constant-current driver for a 24 V strip?

Only if the product’s requirements explicitly match. Constant-current and constant-voltage systems are not interchangeable.

Which assumptions should I check?

Match the units, measurement plane and equipment boundary stated on this page. The starting values and comparison cases are chosen examples, not universal recommendations or current manufacturer ratings.

Where are the formula references?

Published references are listed at the bottom of this page as plain-text website addresses. The example tables are calculated from the displayed method rather than copied from proprietary tables.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.

  • MEAN WELL: LED Driver Power Supply Solution, operating limits and loadinghttps://led.meanwell.com/qa.aspx?c=10
  • NIST SP 811 Appendix B.9: photometric unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9