Lighting calculators / Screens & projectors
Plan the light. Understand the numbers.
Nine-Point Projector Flux Calculator
Measure representative points at the centers of nine equal-area image regions using a suitable illuminance meter and consistent image setup. Their arithmetic mean multiplied by total image area gives an approximate flux arriving on that plane. A central hot spot alone is not representative of the whole image.
Your lighting inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Estimated image flux lm = arithmetic mean of nine equal-area grid readings in lux × image area m².
Calculate an image-flux estimate from nine illuminance readings and the corresponding screen area.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
This arithmetic does not certify ANSI or ISO testing. Grid placement, calibration, ambient subtraction, image setup and standard-specific procedures must be controlled separately.
Nine-point illuminance averages versus advertised projector brightness
Measure representative points at the centers of nine equal-area image regions using a suitable illuminance meter and consistent image setup. Their arithmetic mean multiplied by total image area gives an approximate flux arriving on that plane. A central hot spot alone is not representative of the whole image.
A measurement calculator cannot make an uncontrolled test into a standards-certified result. Account for ambient contribution and instrument response using the applicable procedure. The reported minimum-to-average reading ratio is only a summary of this grid and does not establish a projector’s full image quality.
Continue with: Projector Screen Lumens Calculator · Lux & Nits Surface Calculator · Screen Size & Aspect Ratio Calculator · LED Video Wall Geometry Calculator
Check the numbers
Nine-Point Projector Flux Calculator: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
Projected image area = 4 m²; Illuminance reading 1 = 500 lux; Illuminance reading 2 = 500 lux; Illuminance reading 3 = 500 lux; Illuminance reading 4 = 500 lux; Illuminance reading 5 = 500 lux; Illuminance reading 6 = 500 lux; Illuminance reading 7 = 500 lux; Illuminance reading 8 = 500 lux; Illuminance reading 9 = 500 lux.
| Output | Computed result |
|---|---|
| Nine-point image-flux estimate | 2,000 lm |
| Grid average | 500 lux |
| Grid minimum | 500 lux |
| Minimum / average | 1 ratio |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 1 m² | Projected image area | 500 lm |
| 2 m² | Projected image area | 1,000 lm |
| 3 m² | Projected image area | 1,500 lm |
| 4 m² | Projected image area | 2,000 lm |
| 6 m² | Projected image area | 3,000 lm |
| 8 m² | Projected image area | 4,000 lm |
| 12 m² | Projected image area | 6,000 lm |
Unchanged inputs use: Projected image area = 4 m²; Illuminance reading 1 = 500 lux; Illuminance reading 2 = 500 lux; Illuminance reading 3 = 500 lux; Illuminance reading 4 = 500 lux; Illuminance reading 5 = 500 lux; Illuminance reading 6 = 500 lux; Illuminance reading 7 = 500 lux; Illuminance reading 8 = 500 lux; Illuminance reading 9 = 500 lux. Results retain the model limitations described above.
Common questions
Does this produce certified ANSI lumens?
No. It demonstrates the nine-reading arithmetic. Standard-compliant setup and measurement must be established separately.
Why use nine readings rather than one?
A projected image can vary across its area, so one center reading may not represent its average.
Should I use luminance or illuminance readings?
The inputs here are illuminance in lux at the image plane, not screen luminance in nits.
Does it convert LED lumens to ANSI lumens?
No. It calculates from actual readings rather than an unsupported marketing-unit factor.
Which assumptions should I check?
Match the units, measurement plane and equipment boundary stated on this page. The starting values and comparison cases are chosen examples, not universal recommendations or current manufacturer ratings.
Where are the formula references?
Published references are listed at the bottom of this page as plain-text website addresses. The example tables are calculated from the displayed method rather than copied from proprietary tables.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- Konica Minolta: Language of Light, illuminance meters and nine-point projected fluxhttps://www.konicaminolta.com/instruments/knowledge/light/instrumentation/05.html