Lighting CalculatorPlan light with clear assumptions

Lighting calculators / Screens & projectors

Plan the light. Understand the numbers.

Lux & Nits Surface Calculator

One nit means one candela per square metre of luminance. Lux measures incoming light at the surface, while luminance describes light leaving the surface toward an observer. The relationship needs a reflection model; for an ideal Lambertian surface it includes reflectance and the factor π.

Your lighting inputs

lux
ratio
m²

Starting values are illustrative. Check units and assumptions below. Calculate submits your inputs to this site’s result page.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Ideal diffuse reflected luminance cd/m² = reflectance × lux ÷ π; reflected flux lm = reflectance × lux × area.

Relate lux, diffuse-surface luminance and reflected flux under an ideal Lambertian assumption.

  1. Choose a measurement plane and use compatible units for all inputs.
  2. Obtain appropriate product data or representative measurements for the stated model.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Lux and nits have no universal direct conversion. This model is for an ideal diffuse reflector, not a glossy screen or directional display.

cd/m², nits and reflected lumens

One nit means one candela per square metre of luminance. Lux measures incoming light at the surface, while luminance describes light leaving the surface toward an observer. The relationship needs a reflection model; for an ideal Lambertian surface it includes reflectance and the factor π.

The reflected total flux is reflectance times incident flux over the chosen area. An emitting display’s nits-to-lumens conversion additionally needs emitting area and an angular distribution assumption. Do not apply this diffuse-reflector equation to a directional projector screen, glossy material or LED wall without validating the model.

Check the numbers

Lux & Nits Surface Calculator: calculated examples

These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.

Worked example with stated inputs

Incident illuminance = 500 lux; Diffuse reflectance = 0.8 ratio; Area = 20 m².

OutputComputed result
Ideal diffuse reflected luminance127.323954 cd/m² (nits)
Reflected total flux8,000 lm
Luminous exitance400 lm/m²

How one input changes the answer

ScenarioChanged inputResult
125 luxIncident illuminance31.830989 cd/m² (nits)
250 luxIncident illuminance63.661977 cd/m² (nits)
375 luxIncident illuminance95.492966 cd/m² (nits)
500 luxIncident illuminance127.323954 cd/m² (nits)
750 luxIncident illuminance190.985932 cd/m² (nits)
1000 luxIncident illuminance254.647909 cd/m² (nits)
1500 luxIncident illuminance381.971863 cd/m² (nits)

Unchanged inputs use: Incident illuminance = 500 lux; Diffuse reflectance = 0.8 ratio; Area = 20 m². Results retain the model limitations described above.

Common questions

Can I convert lux to nits directly?

Only with an appropriate surface model. This page uses an explicitly stated diffuse reflectance.

Is one nit one cd/m²?

Yes. Nit is a common name for candela per square metre.

Can I convert lumens to cd/m² without area?

No. Area and angular distribution are required, and emitted versus reflected light must be distinguished.

Does this apply to every projector screen?

No. Screen gain and directionality can depart from ideal diffuse reflection.

Which assumptions should I check?

Match the units, measurement plane and equipment boundary stated on this page. The starting values and comparison cases are chosen examples, not universal recommendations or current manufacturer ratings.

Where are the formula references?

Published references are listed at the bottom of this page as plain-text website addresses. The example tables are calculated from the displayed method rather than copied from proprietary tables.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.

  • Konica Minolta CA-S20w manual: illuminance, luminance and reflectance relationshiphttps://www.konicaminolta.com/instruments/download/instruction_manual/software/pdf/ca-s20w-24x_instruction_eng.pdf
  • NIST SP 811 Appendix B.9: photometric unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9