Lighting CalculatorPlan light with clear assumptions

Lighting calculators / Screens & projectors

Plan the light. Understand the numbers.

LED Video Wall Geometry Calculator

A regular wall’s width is cabinet columns times cabinet width, while its height uses rows and cabinet height. Dividing physical millimetres by pixel pitch gives a nominal pixel count. For four by three 500 mm cabinets at 2.5 mm pitch, the modeled wall is 2 m by 1.5 m with an 800 by 600 nominal raster.

Your lighting inputs

columns
rows
mm
mm
mm

Starting values are illustrative. Check units and assumptions below. Calculate submits your inputs to this site’s result page.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Wall dimensions = cabinet count × cabinet dimension; nominal pixels = physical mm ÷ pitch.

Calculate cabinet count, physical area and nominal resolution for a regular LED video wall.

  1. Choose a measurement plane and use compatible units for all inputs.
  2. Obtain appropriate product data or representative measurements for the stated model.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Actual module/cabinet pixel maps control resolution. Noninteger nominal pixels are flagged; this does not validate a receiving-card map, brand product or structural installation.

LED screen pixels, pitch and cabinet layout

A regular wall’s width is cabinet columns times cabinet width, while its height uses rows and cabinet height. Dividing physical millimetres by pixel pitch gives a nominal pixel count. For four by three 500 mm cabinets at 2.5 mm pitch, the modeled wall is 2 m by 1.5 m with an 800 by 600 nominal raster.

Absen, ROE, Samsung, Planar and Unilumin products can have specific cabinet dimensions, module maps and controller limits. This page does not contain their catalogs or act as an official 4wall Entertainment calculator. Verify actual pixel counts rather than rounding a fractional pitch result into a claim of supported hardware.

Check the numbers

LED Video Wall Geometry Calculator: calculated examples

These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.

Worked example with stated inputs

Cabinet columns = 4 columns; Cabinet rows = 3 rows; Cabinet width = 500 mm; Cabinet height = 500 mm; Pixel pitch = 2.5 mm.

OutputComputed result
Regular LED wall cabinet count12 cabinets
Physical width2 m
Physical height1.5 m
Wall area3 m²
Nominal pixel columns800 pixels
Nominal pixel rows600 pixels
Nominal aspect ratio1.333333 width/height
Pixel consistencyWhole nominal counts; verify actual map

How one input changes the answer

ScenarioChanged inputResult
1 columnsCabinet columns3 cabinets
2 columnsCabinet columns6 cabinets
3 columnsCabinet columns9 cabinets
4 columnsCabinet columns12 cabinets
6 columnsCabinet columns18 cabinets
8 columnsCabinet columns24 cabinets
12 columnsCabinet columns36 cabinets

Unchanged inputs use: Cabinet columns = 4 columns; Cabinet rows = 3 rows; Cabinet width = 500 mm; Cabinet height = 500 mm; Pixel pitch = 2.5 mm. Results retain the model limitations described above.

Common questions

Does a 16:9 cabinet arrangement guarantee a 16:9 image?

Only when the physical and pixel dimensions also yield that ratio. Use actual cabinet proportions and pixel maps.

Why can nominal resolution be noninteger?

The entered pitch and dimensions may be rounded or incompatible. The exact manufacturer pixel map takes precedence.

Can I calculate minimum viewing distance from pitch?

There is no universal distance that guarantees acceptable image quality for every viewer and content. This tool does not impose a marketing rule.

Does this choose a video controller?

No. Receiver configuration, processing capacity, refresh and signal routing are outside the geometry model.

Which assumptions should I check?

Match the units, measurement plane and equipment boundary stated on this page. The starting values and comparison cases are chosen examples, not universal recommendations or current manufacturer ratings.

Where are the formula references?

Published references are listed at the bottom of this page as plain-text website addresses. The example tables are calculated from the displayed method rather than copied from proprietary tables.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.

  • NIST SP 811 Appendix B.9: photometric unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9