Lighting CalculatorPlan light with clear assumptions

Lighting calculators / Light & unit conversions

Plan the light. Understand the numbers.

Lux & Foot-Candle Converter

Foot-candle, footcandle and fc are common ways to label the same illuminance unit. They do not mean total candles or candlepower. The factor follows from the exact area relationship between the international foot and metre, rather than a guessed ten-to-one brightness ratio.

Your lighting inputs

Starting values are illustrative. Check units and assumptions below. Calculate submits your inputs to this site’s result page.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

1 foot-candle = 1 lm/ft² = 10.7639104167 lux; fc = lux ÷ 10.7639104167.

Convert lux and foot-candles as two units of illuminance at the same measured surface.

  1. Choose a measurement plane and use compatible units for all inputs.
  2. Obtain appropriate product data or representative measurements for the stated model.
  3. Submit the form, then interpret the result with the assumptions and limits below.

This is a unit conversion, not a recommendation for a room type or a measurement of fixture output.

Lux to fc, footcandles to lux and measurement reports

Foot-candle, footcandle and fc are common ways to label the same illuminance unit. They do not mean total candles or candlepower. The factor follows from the exact area relationship between the international foot and metre, rather than a guessed ten-to-one brightness ratio.

Use this when reading a US photometric report or comparing it with a lux-based target. Conversion does not change the measurement plane, maintenance basis or minimum-versus-average definition. Keep those definitions matched before concluding that one report satisfies another requirement.

Check the numbers

Lux & Foot-Candle Converter: calculated examples

These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.

Worked example with stated inputs

Illuminance value = 100 ; Calculation direction = Lux to foot-candles.

OutputComputed result
Converted illuminance9.290304 fc

How one input changes the answer

ScenarioChanged inputResult
25 Illuminance value2.322576 fc
50 Illuminance value4.645152 fc
75 Illuminance value6.967728 fc
100 Illuminance value9.290304 fc
150 Illuminance value13.935456 fc
200 Illuminance value18.580608 fc
300 Illuminance value27.870912 fc

Unchanged inputs use: Illuminance value = 100 ; Calculation direction = Lux to foot-candles. Results retain the model limitations described above.

Common questions

What is 100 lux in foot-candles?

About 9.290304 fc. At 1,000 lux the result is about 92.90304 fc.

Is one foot-candle exactly ten lux?

No. Ten is a rough approximation; the conversion is about 10.7639104167 lux per fc.

Can I convert foot-candles to watts?

Not directly. You need area, delivered lumens and a suitable efficacy or complete lighting model.

Is candlepower the same as foot-candles?

No. Candlepower commonly refers to candela, a luminous intensity. Foot-candles measure illuminance at a surface.

Which assumptions should I check?

Match the units, measurement plane and equipment boundary stated on this page. The starting values and comparison cases are chosen examples, not universal recommendations or current manufacturer ratings.

Where are the formula references?

Published references are listed at the bottom of this page as plain-text website addresses. The example tables are calculated from the displayed method rather than copied from proprietary tables.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.

  • NIST SP 811 Appendix B.9: photometric unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9