Lighting calculators / Light & unit conversions
Plan the light. Understand the numbers.
Lumens & Watts Calculator
A watts-to-lumens calculation needs luminous efficacy because wattage alone measures electrical input. At a chosen 100 lm/W, 1,100 lm corresponds to 11 W and 2,000 lm to 20 W. Those are calculated scenarios, not performance promises for every LED bulb.
Your lighting inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Lumens = electrical input watts × efficacy lm/W; input watts = lumens ÷ efficacy.
Convert light output and electrical input using an explicitly supplied product luminous efficacy.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
No universal LED, halogen or incandescent conversion ratio exists. Use complete product efficacy; 683 lm/W for monochromatic radiation is a different quantity.
LED wattage, lumen output and replacement charts
A watts-to-lumens calculation needs luminous efficacy because wattage alone measures electrical input. At a chosen 100 lm/W, 1,100 lm corresponds to 11 W and 2,000 lm to 20 W. Those are calculated scenarios, not performance promises for every LED bulb.
For a replacement, compare lumen ratings and actual electrical watts on product labels. A 60 W equivalent LED is not necessarily a 60 W load. Halogen, fluorescent and LED efficacy varies with the product, driver, operating temperature and dimming state. The table below shows arithmetic using stated assumptions rather than reproducing a copyrighted lamp chart.
Continue with: Lumens & Lux Calculator · Lux & Foot-Candle Converter · Lighting Efficacy Calculator · Candela & Lumens Calculator
Check the numbers
Lumens & Watts Calculator: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
Known quantity = 1100 ; Electrical luminous efficacy = 100 lm/W; Calculation direction = Lumens to input watts.
| Output | Computed result |
|---|---|
| Efficacy-based conversion | 11 W |
| Assumed electrical efficacy | 100 lm/W |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 275 | Known quantity | 2.75 W |
| 550 | Known quantity | 5.5 W |
| 825 | Known quantity | 8.25 W |
| 1100 | Known quantity | 11 W |
| 1650 | Known quantity | 16.5 W |
| 2200 | Known quantity | 22 W |
| 3300 | Known quantity | 33 W |
Unchanged inputs use: Known quantity = 1100 ; Electrical luminous efficacy = 100 lm/W; Calculation direction = Lumens to input watts. Results retain the model limitations described above.
Common questions
How many watts is 1,500 lumens?
At 100 lm/W it is 15 W. At another efficacy the result changes, so the product rating must be specified.
Can I convert 60 watts directly to LED watts?
No universal ratio applies. Find the required lumens, then divide by the selected LED product’s lm/W.
Can I convert lumens to kelvin or color temperature?
No. Color temperature describes chromatic appearance; luminous flux describes amount of visible light.
Can I add RGB channel lumens?
Measured channel outputs can be added under matching operating conditions, but RGB color mixing and channel efficacy cannot be inferred from total electrical watts alone.
Can I use a fixed incandescent-to-LED or halogen-to-LED watt conversion?
No. Establish matching useful light output and then use the actual new product efficacy. A fixed electrical-watt multiplier can misstate both brightness and consumption.
Which assumptions should I check?
Match the units, measurement plane and equipment boundary stated on this page. The starting values and comparison cases are chosen examples, not universal recommendations or current manufacturer ratings.
Where are the formula references?
Published references are listed at the bottom of this page as plain-text website addresses. The example tables are calculated from the displayed method rather than copied from proprietary tables.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- US Federal Trade Commission: Shopping for Light Bulbs; lumens versus input wattshttps://consumer.ftc.gov/articles/shopping-light-bulbs
- NIST: Realization of the candela and photometric spectral weightinghttps://www.nist.gov/pml/sensor-science/optical-radiation/realization-candela