Lighting CalculatorPlan light with clear assumptions

Lighting calculators / LED circuits & power

Plan the light. Understand the numbers.

LED Lighting Voltage Drop Calculator

A supply-and-return pair has twice the one-way cable length. Enter resistance for one conductor per metre, not a loop value that already includes the return path. Use resistance data appropriate to material, conductor size and temperature. A percentage voltage drop is relative to the entered source voltage.

Your lighting inputs

V
A
m
mΩ/m

Starting values are illustrative. Check units and assumptions below. Calculate submits your inputs to this site’s result page.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Loop resistance Ω = 2 × one-way metres × mΩ/m ÷ 1,000; drop V = current × loop Ω.

Calculate two-conductor DC voltage drop for an explicitly modeled load at the cable end.

  1. Choose a measurement plane and use compatible units for all inputs.
  2. Obtain appropriate product data or representative measurements for the stated model.
  3. Submit the form, then interpret the result with the assumptions and limits below.

This is not ampacity or wire-size selection. Distributed strips, multiple taps, transformer regulation, AC reactance and temperature effects require an appropriate extended model.

Low-voltage landscape and LED strip feed voltage drop

A supply-and-return pair has twice the one-way cable length. Enter resistance for one conductor per metre, not a loop value that already includes the return path. Use resistance data appropriate to material, conductor size and temperature. A percentage voltage drop is relative to the entered source voltage.

The end-load model assumes all current travels the entire route. A uniformly distributed strip or several landscape fixtures draw different currents along different cable segments, so analyze segments rather than applying one far-end formula blindly. This tool does not choose an AWG size or imply that WAC, FX or other brand wiring limits have been checked.

Check the numbers

LED Lighting Voltage Drop Calculator: calculated examples

These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.

Worked example with stated inputs

Source DC voltage = 24 V; End-load current = 3 A; One-way cable length = 10 m; Resistance per conductor length = 8.2 mΩ/m.

OutputComputed result
DC cable voltage drop0.492 V
Drop percentage2.05 %
Modeled end voltage23.508 V
Loop resistance0.164 Ω
Cable dissipation1.476 W

How one input changes the answer

ScenarioChanged inputResult
2.5 mOne-way cable length0.123 V
5 mOne-way cable length0.246 V
7.5 mOne-way cable length0.369 V
10 mOne-way cable length0.492 V
15 mOne-way cable length0.738 V
20 mOne-way cable length0.984 V
30 mOne-way cable length1.476 V

Unchanged inputs use: Source DC voltage = 24 V; End-load current = 3 A; One-way cable length = 10 m; Resistance per conductor length = 8.2 mΩ/m. Results retain the model limitations described above.

Common questions

Does this include the return conductor?

Yes. The equation doubles the entered one-way length. Do not enter the already-doubled loop length.

Can I calculate lighting wire size here?

Not completely. Voltage drop is one consideration; ampacity, protection, installation conditions and permitted product wiring also matter.

Can I use it for an AC landscape transformer?

The present model is DC resistance only. AC regulation and reactance are not modeled.

Why is the load voltage rejected at zero or below?

At that point the assumed current/source model is not a usable lighting supply scenario. Reduce resistance/current or reassess the system.

Which assumptions should I check?

Match the units, measurement plane and equipment boundary stated on this page. The starting values and comparison cases are chosen examples, not universal recommendations or current manufacturer ratings.

Where are the formula references?

Published references are listed at the bottom of this page as plain-text website addresses. The example tables are calculated from the displayed method rather than copied from proprietary tables.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.

  • NIST SP 811 Appendix B.9: photometric unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9
  • MEAN WELL: LED Driver Power Supply Solution, operating limits and loadinghttps://led.meanwell.com/qa.aspx?c=10