Lighting calculators / LED circuits & power
Plan the light. Understand the numbers.
LED Resistor Calculator
Subtract the LED string’s forward-voltage sum from the supply to find the voltage across each resistor. Divide by the desired branch current in amperes. At 12 V with three 2 V LEDs and 20 mA, the theoretical resistance is 300 Ω and the resistor dissipates 0.12 W at that assumed operating point.
Your lighting inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
R per branch = (supply V − series count × Vf)/branch A; resistor W = branch A² × R.
Calculate a theoretical series resistance and resistor dissipation for one or more independently resisted LED branches.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
This fixed-Vf DC model does not regulate high-power LEDs or select a resistor’s thermal rating. Each parallel branch needs its own current control; do not share one resistor across unmatched LEDs.
5 V, 12 V, series and parallel LED resistor calculations
Subtract the LED string’s forward-voltage sum from the supply to find the voltage across each resistor. Divide by the desired branch current in amperes. At 12 V with three 2 V LEDs and 20 mA, the theoretical resistance is 300 Ω and the resistor dissipates 0.12 W at that assumed operating point.
Real LEDs have a range of forward voltage that changes with current and temperature. Select a practical resistance and verify worst-case current and component power ratings with suitable margin. This tool reports theoretical arithmetic, not an approved parts list or a replacement for a regulated high-power LED driver.
Continue with: Lighting Power Density Calculator · General Lighting Load Calculator · Connected Lighting Load Calculator · LED Strip Power Supply Calculator
Check the numbers
LED Resistor Calculator: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
DC supply voltage = 12 V; Forward voltage per LED = 2 V; LEDs in each series branch = 3 LEDs; Desired current per branch = 20 mA; Identical separately resisted branches = 1 branches.
| Output | Computed result |
|---|---|
| Theoretical resistance per branch | 300 Ω |
| Nominal resistor dissipation per branch | 0.12 W |
| Total nominal supply current | 0.02 A |
| Total nominal resistor heat | 0.12 W |
| LED string voltage | 6 V |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 9 V | DC supply voltage | 150 Ω |
| 12 V | DC supply voltage | 300 Ω |
| 18 V | DC supply voltage | 600 Ω |
| 24 V | DC supply voltage | 900 Ω |
| 36 V | DC supply voltage | 1,500 Ω |
Unchanged inputs use: DC supply voltage = 12 V; Forward voltage per LED = 2 V; LEDs in each series branch = 3 LEDs; Desired current per branch = 20 mA; Identical separately resisted branches = 1 branches. Results retain the model limitations described above.
Common questions
How do I calculate a resistor for an LED?
Use the supply minus total series forward voltage, divided by desired current in amperes.
Can I enter milliamps?
Yes. The form converts mA to A internally; 20 mA is 0.02 A.
Does it support parallel LEDs?
Only as identical branches with a separate resistor in each branch. It does not endorse a single shared resistor for unmatched parallel LEDs.
Is calculated dissipation the required rated wattage?
No. It is the nominal heat in the resistor. Allow for tolerances, worst-case supply/Vf and thermal derating when selecting a component.
Which assumptions should I check?
Match the units, measurement plane and equipment boundary stated on this page. The starting values and comparison cases are chosen examples, not universal recommendations or current manufacturer ratings.
Where are the formula references?
Published references are listed at the bottom of this page as plain-text website addresses. The example tables are calculated from the displayed method rather than copied from proprietary tables.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- Jameco Electronics: LED Series Resistor Calculator and Ohm’s lawhttps://www.jameco.com/Jameco/conversion-calculators/led-series-resistor-calculator.html