Lighting calculators / LED circuits & power
Plan the light. Understand the numbers.
Constant-Current LED Driver Calculator
A constant-current LED driver regulates current while its output voltage follows the connected LED string within a specified operating window. Multiply the minimum and maximum LED forward voltages by the series count, considering the data-sheet conditions behind those limits. The driver’s permissible output range must encompass the string over expected conditions.
Your lighting inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
String voltage range = series count × individual Vf range; maximum output W = count × Vfmax × current A.
Calculate the required output-voltage span and nominal maximum output power of a series LED string.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
The driver must support the operating current and entire voltage window under its actual ratings. This does not approve a driver model or allow unbalanced parallel LED strings.
Constant-current string voltage and driver compatibility
A constant-current LED driver regulates current while its output voltage follows the connected LED string within a specified operating window. Multiply the minimum and maximum LED forward voltages by the series count, considering the data-sheet conditions behind those limits. The driver’s permissible output range must encompass the string over expected conditions.
Voltage alone is insufficient: startup behavior, dimming, isolation, thermal limits and maximum rated output also matter. Parallel strings can require individual current regulation or balancing; simply multiplying string count does not ensure equal current. The constant-voltage strip tool addresses a different supply type.
Continue with: Lighting Power Density Calculator · General Lighting Load Calculator · Connected Lighting Load Calculator · LED Strip Power Supply Calculator
Check the numbers
Constant-Current LED Driver Calculator: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
LEDs in series = 6 LEDs; Minimum forward voltage per LED = 2.8 V; Maximum forward voltage per LED = 3.2 V; String operating current = 350 mA.
| Output | Computed result |
|---|---|
| Maximum nominal string output power | 6.72 W |
| Minimum series voltage | 16.8 V |
| Maximum series voltage | 19.2 V |
| Required regulated current | 350 mA |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 2 LEDs | LEDs in series | 2.24 W |
| 3 LEDs | LEDs in series | 3.36 W |
| 4 LEDs | LEDs in series | 4.48 W |
| 6 LEDs | LEDs in series | 6.72 W |
| 9 LEDs | LEDs in series | 10.08 W |
| 12 LEDs | LEDs in series | 13.44 W |
| 18 LEDs | LEDs in series | 20.16 W |
Unchanged inputs use: LEDs in series = 6 LEDs; Minimum forward voltage per LED = 2.8 V; Maximum forward voltage per LED = 3.2 V; String operating current = 350 mA. Results retain the model limitations described above.
Common questions
How do I calculate LED driver wattage?
For the stated series string, multiply its output voltage by current. Use the maximum relevant Vf for the maximum nominal output power shown.
Can I select a driver only by watts?
No. Its regulated current and allowed output-voltage range are essential.
What if minimum Vf exceeds maximum Vf?
Those inputs are inconsistent and are rejected.
Does this design parallel constant-current strings?
No. It calculates one series string and does not establish current sharing or channel topology.
Which assumptions should I check?
Match the units, measurement plane and equipment boundary stated on this page. The starting values and comparison cases are chosen examples, not universal recommendations or current manufacturer ratings.
Where are the formula references?
Published references are listed at the bottom of this page as plain-text website addresses. The example tables are calculated from the displayed method rather than copied from proprietary tables.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- MEAN WELL: LED Driver Power Supply Solution, operating limits and loadinghttps://led.meanwell.com/qa.aspx?c=10
- Jameco Electronics: LED Series Resistor Calculator and Ohm’s lawhttps://www.jameco.com/Jameco/conversion-calculators/led-series-resistor-calculator.html