Lighting CalculatorPlan light with clear assumptions

Lighting calculators / Rooms & layouts

Plan the light. Understand the numbers.

Room Cavity Ratio Calculator

Room cavity ratio describes the proportions of the cavity between luminaires and the working plane. Keep length, width and height in the same unit. It is dimensionless, so converting all three consistently from feet to metres does not change the ratio.

Your lighting inputs

m
m
m

Starting values are illustrative. Check units and assumptions below. Calculate submits your inputs to this site’s result page.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

RCR = 5 × cavity height × (length + width) ÷ (length × width).

Calculate room cavity ratio to help select a coefficient of utilization from appropriate luminaire data.

  1. Choose a measurement plane and use compatible units for all inputs.
  2. Obtain appropriate product data or representative measurements for the stated model.
  3. Submit the form, then interpret the result with the assumptions and limits below.

RCR does not determine CU by itself. Surface reflectances, distribution and the manufacturer’s tabulation are still required.

Use room geometry without inventing a utilization coefficient

Room cavity ratio describes the proportions of the cavity between luminaires and the working plane. Keep length, width and height in the same unit. It is dimensionless, so converting all three consistently from feet to metres does not change the ratio.

Once RCR is known, consult the relevant product’s coefficient-of-utilization information with the correct ceiling and wall reflectances. This tool does not supply proprietary CU tables or substitute a generic coefficient for every room. Higher walls and a narrow room can alter utilization even when floor area is unchanged.

Check the numbers

Room Cavity Ratio Calculator: calculated examples

These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.

Worked example with stated inputs

Room length = 5 m; Room width = 4 m; Luminaire-to-workplane height = 2.5 m.

OutputComputed result
Room cavity ratio5.625 ratio
Working-plane area20 m²

How one input changes the answer

ScenarioChanged inputResult
0.625 mLuminaire-to-workplane height1.40625 ratio
1.25 mLuminaire-to-workplane height2.8125 ratio
1.875 mLuminaire-to-workplane height4.21875 ratio
2.5 mLuminaire-to-workplane height5.625 ratio
3.75 mLuminaire-to-workplane height8.4375 ratio
5 mLuminaire-to-workplane height11.25 ratio
7.5 mLuminaire-to-workplane height16.875 ratio

Unchanged inputs use: Room length = 5 m; Room width = 4 m; Luminaire-to-workplane height = 2.5 m. Results retain the model limitations described above.

Common questions

What height goes into RCR?

Use the vertical distance from the luminaire plane to the selected working plane.

Can I calculate CU from RCR automatically?

Not reliably without product distribution and surface reflectance information. This tool deliberately does not guess a CU.

Is RCR measured in metres?

No. It is dimensionless. The dimensions inside the equation must simply share a unit.

Can I use this for an irregular room?

A single rectangle may not represent complex geometry. Divide or model the space with an appropriate photometric method.

Which assumptions should I check?

Match the units, measurement plane and equipment boundary stated on this page. The starting values and comparison cases are chosen examples, not universal recommendations or current manufacturer ratings.

Where are the formula references?

Published references are listed at the bottom of this page as plain-text website addresses. The example tables are calculated from the displayed method rather than copied from proprietary tables.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.

  • UC Davis California Lighting Technology Center: High-Efficacy Residential Lighting, lumen method and room cavity ratiohttps://cltc.ucdavis.edu/sites/g/files/dgvnsk12206/files/media/documents/high-efficacy-residential-lighting-guide-dec14.pdf