Lighting calculators / Rooms & layouts
Plan the light. Understand the numbers.
Recessed Lighting Layout Calculator
An evenly spaced ceiling grid can use a half-spacing setback at each wall. With three columns along a five-metre room, centers are 1.6667 m apart and the first center is about 0.8333 m from the end wall. Each axis is independent, so a rectangular room need not use square spacing.
Your lighting inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Count = columns × rows; center spacing = dimension ÷ count on that axis; wall offset = half the spacing.
Lay out an evenly spaced rectangular grid of recessed, pot or can lights with half-spacing wall offsets.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
This is geometry only. It does not choose a light level, avoid joists or obstacles, or verify the beam pattern or glare.
Downlight positions, kitchen can lights and rectangular ceiling grids
An evenly spaced ceiling grid can use a half-spacing setback at each wall. With three columns along a five-metre room, centers are 1.6667 m apart and the first center is about 0.8333 m from the end wall. Each axis is independent, so a rectangular room need not use square spacing.
Use the position lists as a preliminary layout sketch, then check the selected luminaire’s photometry and the room’s actual features. Kitchen cabinets, islands, beams, fans and work surfaces often justify a nonuniform arrangement. This tool is not an obstacle-aware placement engine and does not automatically choose how many recessed lights are needed.
Continue with: Room Lighting Calculator · Average Room Lux Calculator · Lighting Spacing Criterion Calculator · Room Cavity Ratio Calculator
Check the numbers
Recessed Lighting Layout Calculator: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
Room length = 5 m; Room width = 4 m; Columns along room length = 3 columns; Rows across room width = 2 rows.
| Output | Computed result |
|---|---|
| Rectangular grid count | 6 fixtures |
| Length-axis spacing | 1.666667 m |
| Width-axis spacing | 2 m |
| Length-end wall offset | 0.833333 m |
| Side-wall offset | 1 m |
| Length-axis centers | 0.833333, 2.5, 4.166667 m |
| Width-axis centers | 1, 3 m |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 1 columns | Columns along room length | 2 fixtures |
| 2 columns | Columns along room length | 4 fixtures |
| 3 columns | Columns along room length | 6 fixtures |
| 4 columns | Columns along room length | 8 fixtures |
| 6 columns | Columns along room length | 12 fixtures |
| 9 columns | Columns along room length | 18 fixtures |
Unchanged inputs use: Room length = 5 m; Room width = 4 m; Columns along room length = 3 columns; Rows across room width = 2 rows. Results retain the model limitations described above.
Common questions
How many recessed lights do I need?
Estimate a fixture count with the room lumen method, then choose practical rows and columns here. Geometry alone cannot determine the required light output.
Are can lights and pot lights calculated differently?
The rectangular center-position geometry is the same. Product distribution and architectural constraints can require different layouts.
Can I use feet for the room dimensions?
The form is labeled in metres. Multiply feet by 0.3048 before entering them; all position results are then metres.
Does this calculate placement around obstacles?
No. It creates a regular grid with symmetric half-spacing offsets. Review obstructions and intended tasks separately.
Which assumptions should I check?
Match the units, measurement plane and equipment boundary stated on this page. The starting values and comparison cases are chosen examples, not universal recommendations or current manufacturer ratings.
Where are the formula references?
Published references are listed at the bottom of this page as plain-text website addresses. The example tables are calculated from the displayed method rather than copied from proprietary tables.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- UC Davis California Lighting Technology Center: High-Efficacy Residential Lighting, lumen method and room cavity ratiohttps://cltc.ucdavis.edu/sites/g/files/dgvnsk12206/files/media/documents/high-efficacy-residential-lighting-guide-dec14.pdf