Lighting calculators / Rooms & layouts
Plan the light. Understand the numbers.
Average Room Lux Calculator
Start with initial output for the complete luminaire, not an unrelated bare LED chip figure. The utilization coefficient represents how much of that output contributes to the chosen working plane. The loss factor represents the modeled maintained condition. If your lumen figure already includes a particular loss, avoid applying the same reduction twice.
Your lighting inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Average maintained lux = fixture count × fixture lumens × CU × LLF ÷ room area.
Estimate the maintained average light level from an existing fixture count and room geometry.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
This is an average work-plane estimate, not a lux measurement, minimum light level or glare calculation.
Check average lux for an existing room lighting proposal
Start with initial output for the complete luminaire, not an unrelated bare LED chip figure. The utilization coefficient represents how much of that output contributes to the chosen working plane. The loss factor represents the modeled maintained condition. If your lumen figure already includes a particular loss, avoid applying the same reduction twice.
The result can help compare an eight-fixture and a ten-fixture proposal for the same room. A mean value does not reveal dark corners or bright spots. Brand searches for Lithonia, Metalux, Signify, GE, Osram, Vonn or Roblon still need actual photometric data; this page does not provide a brand catalog or official software.
Continue with: Room Lighting Calculator · Recessed Lighting Layout Calculator · Lighting Spacing Criterion Calculator · Room Cavity Ratio Calculator
Check the numbers
Average Room Lux Calculator: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
Room length = 5 m; Room width = 4 m; Installed luminaires = 8 fixtures; Initial output per luminaire = 1800 lm; Coefficient of utilization = 0.6 ratio; Light loss factor = 0.8 ratio.
| Output | Computed result |
|---|---|
| Modeled average maintained illuminance | 345.6 lux |
| Equivalent illuminance | 32.107291 fc |
| Room area | 20 m² |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 2 fixtures | Installed luminaires | 86.4 lux |
| 4 fixtures | Installed luminaires | 172.8 lux |
| 6 fixtures | Installed luminaires | 259.2 lux |
| 8 fixtures | Installed luminaires | 345.6 lux |
| 12 fixtures | Installed luminaires | 518.4 lux |
| 16 fixtures | Installed luminaires | 691.2 lux |
| 24 fixtures | Installed luminaires | 1,036.8 lux |
Unchanged inputs use: Room length = 5 m; Room width = 4 m; Installed luminaires = 8 fixtures; Initial output per luminaire = 1800 lm; Coefficient of utilization = 0.6 ratio; Light loss factor = 0.8 ratio. Results retain the model limitations described above.
Common questions
How do I calculate average lux level?
Multiply the total initial output by CU and LLF, then divide by square metres of the working plane.
Does a higher average guarantee better lighting?
No. Uniformity, glare, contrast, task orientation and control behavior also affect useful lighting.
Can I enter lumens from a manufacturer?
Yes, when they describe the full luminaire at the relevant operating condition. Check whether the data already includes any maintenance reduction.
Can I calculate outdoor or parking-lot lighting this way?
Only as a very rough average energy/flux allocation with justified factors. Roadways and parking sites normally need a point-by-point photometric analysis.
Which assumptions should I check?
Match the units, measurement plane and equipment boundary stated on this page. The starting values and comparison cases are chosen examples, not universal recommendations or current manufacturer ratings.
Where are the formula references?
Published references are listed at the bottom of this page as plain-text website addresses. The example tables are calculated from the displayed method rather than copied from proprietary tables.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- UC Davis California Lighting Technology Center: High-Efficacy Residential Lighting, lumen method and room cavity ratiohttps://cltc.ucdavis.edu/sites/g/files/dgvnsk12206/files/media/documents/high-efficacy-residential-lighting-guide-dec14.pdf
- NIST SP 811 Appendix B.9: photometric unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9